Product Description Product DescriptionThe Mitutoyo 500-784 is one of Mitutoyo?€™s Series 500 MyCal Solar Absolute Digimatic Calipers and measures 0?€ to 6?€ or 0 to 150 mm with +/- 0.001?€ or +/- 0.010 mm accuracy. It is made of durable hardened stainless steel and uses Mitutoyo?€™s ABSOLUTE linear encoder technology. Coolant-proof, it meets IP 67 standards with a dust-tight, waterproof, oil-proof, and damage-resistant construction. Its hard-coated solar panels protect the solar cells storing energy for operation. Through solar power, you can measure in any location without the need to replace batteries. This digital solar caliper has .295-inch/7.4-mm LCD characters with a five-digit display and easy-to-reach function control buttons, such as Inch/Metric to convert from inch to metric measurements and On/Off to automatically shut off the caliper after 30 minutes. Its solar battery retains its origin point for life , without requiring the caliper to zero-set its LCD display due to low light intensity. Although identical to dial and vernier calipers in its ability to make precise measurements, this digital solar caliper also has the LCD, which clearly shows values and increases reading reliability over the other types. The 500-784?€™s LCD also reflects all ABSOLUTE system activities. The Absolute Scale function tracks the origin point?€”even after shutoff. In environments with available light of 60 Lux or more, the caliper becomes active and you can immediately start measuring, without zero resetting or worrying about overspeed errors. You can make and compare incremental measurements without having to subtract the first measurement from the second. The 500-784 is IP67 rated for dust, water, and oil protection. It has the ABSOLUTE electromagnetic induction linear encoder and hard-coated solar panels, for increased durability in storing energy in solar cells for safe operation. It weighs approximately 1 lb and measures outer diameter , inner diameter , depth, and step, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer "steps" are measured. Outside Jaw Depth is 1.57?€/ 39.87 mm, Inside Jaw Depth is .65?€/16.51 mm, Upper Jaw Length is 1.57?€/ 39.87 mm, and Lower Jaw Length is 1.57?€/ 39.87 mm. Range is 0 to 6"/0 to 150 mm, LCD Resolution is .0005"/0.01 mm, Repeatability is .0005"/0.01 mm, and Accuracy is rated + or - 0.0001"/0.02 mm. Also included are inch/metric and on/off automatic shutoff function buttons. A Digital LCD Data Reading Hold function is available with the optional Data Hold Unit , sold separately. An alarm alerts the user to low voltage and scale contamination and counting value composition errors. A rolling thumb wheel makes fine adjustments and a thumb screw locks the scale?€™s position. Response speed is unlimited. The caliper has no SPC output capability. The built-in solar cells can store energy for up to three hours of caliper operation. The caliper can be used continuously above 60 Lux ambient illumination. Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, machining, manufacturing, carpentry, and medicine. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers all give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to the main scale for an additional, fractional reading to improve measurement precision. The dial caliper has a circular dial with a pointer on a toothed gear rack replacing the second vernier scale. As with the vernier, this second measurement is added to the reading from the main scale to obtain the result. The dial caliper is used also for measuring size differential between two objects. The digital caliper takes the same sort of differential measurements as the dial caliper by zeroing the display at any point along the slide, with an LCD that displays a single, easily read value in both English and metric units. Some digital calipers can hold data readings between measurements and send them to data collection devices. Founded in Tokyo in 1934, Mitutoyo is a leader in the metrology field, producing high-quality measurement products, including mechanical, dimensional gauging products, focusing on micrometers, calipers, indicators, and other measurement tools, as well as output gauges, interfaces, data collectors, and analysis software. Mitutoyo formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, Illinois, with additional locations in the U.S. and Canada. The Mitutoyo 500-784 comes in a fitted, plastic case.
Product Description Mitutoyo 500-784, IP67 Solar Digimatic Digital Caliper, 0 - 6"/150mm, .0005"/0.01mm, Non-Output
Read More
